245/40R18 vs 255/40R18
255/40R18 is +0.31″ in overall diameter and +10 mm in section width against 245/40R18 — a diameter change of +1.22%, which stays inside the ±3% substitution rule. An indicated 60 mph would really be 60.7 mph.
Every dimension
| Dimension | 245/40R18 → 255/40R18 | Change |
|---|---|---|
| Overall diameter | 25.72″ → 26.03″ | +0.31″ (+1.22%) |
| Section width | 245 mm → 255 mm | +10 mm (+4.08%) |
| Sidewall height | 98.0 mm → 102.0 mm | +4.0 mm |
| Rolling circumference | 80.79″ → 81.78″ | +0.99″ |
| Revolutions per mile | 784.2 → 774.8 | −9.5 |
| Axle height / clearance | 12.86″ → 13.02″ | +0.16″ |
Which is taller, 245/40R18 or 255/40R18?
255/40R18 is the taller of the two, at 26.03″ against 25.72″. The gap is 0.31 inches, or 8.0 mm.
Both are metric sizes, so neither states its height directly. Both figures below are derived from the section width, aspect ratio and wheel diameter in the code. 245/40R18 is 245 mm wide with a 98.0 mm sidewall on a 18″ wheel; 255/40R18 is 255 mm wide with a 102.0 mm sidewall on a 18″ wheel.
What the speedometer will read
| Speedometer reads | Actual speed | Error |
|---|---|---|
| 25 mph | 25.3 mph | +0.3 mph |
| 40 mph | 40.5 mph | +0.5 mph |
| 55 mph | 55.7 mph | +0.7 mph |
| 60 mph | 60.7 mph | +0.7 mph |
| 70 mph | 70.9 mph | +0.9 mph |
| 80 mph | 81.0 mph | +1.0 mph |
Fitting 255/40R18 in place of 245/40R18 multiplies every speed and distance reading by 1.01225. Over 10,000 indicated miles the odometer is out by +122 miles.
Effective gearing moves by the same proportion. A vehicle with 3.73 axles running 245/40R18 would need 3.78 to keep the same engine speed on 255/40R18. Work it out for your own axle ratio.
Full specification of each size
245/40R18
| Dimension | Metric | Imperial |
|---|---|---|
| Section width | 245.0 mm | 9.65″ |
| Sidewall height | 98.0 mm | 3.86″ |
| Wheel diameter | 457.2 mm | 18.0″ |
| Overall diameter | 653.2 mm | 25.72″ |
| Rolling circumference | 2,052.1 mm | 80.79″ |
| Revolutions per mile | 487.3 / km | 784.2 / mile |
| Measuring rim (estimate) | 216 mm | 8.5″ |
255/40R18
| Dimension | Metric | Imperial |
|---|---|---|
| Section width | 255.0 mm | 10.04″ |
| Sidewall height | 102.0 mm | 4.02″ |
| Wheel diameter | 457.2 mm | 18.0″ |
| Overall diameter | 661.2 mm | 26.03″ |
| Rolling circumference | 2,077.2 mm | 81.78″ |
| Revolutions per mile | 481.4 / km | 774.8 / mile |
| Measuring rim (estimate) | 229 mm | 9″ |
Rim widths differ too: 245/40R18 is designed for 8″–9.5″ and 255/40R18 for 8.5″–10″. Their measuring rims differ, so the same wheel will not be ideal for both.
Can you swap one for the other?
Inside the ±3% rule
The diameter difference of +1.22% is within the ±3% that fitters use as the boundary for a substitution, so the speedometer, odometer and wheel-speed-derived systems stay close enough to calibration. The section width difference of +10 mm is a separate question and is the one that decides whether it rubs.
Neither figure says anything about physical fitment. Whether 255/40R18 clears the strut, the fender liner and the steering stops depends on wheel offset and suspension geometry that a size code does not encode. For maintenance rather than sizing, Car Basics covers tire care.
245/40R18 vs 255/40R18: common questions
- Is 255/40R18 bigger than 245/40R18?
- 255/40R18 is 0.31 inches taller and 10 mm wider. In overall diameter that is +1.22%, which stays inside the ±3% rule of thumb for a substitution.
- How much will 255/40R18 throw off my speedometer?
- Every reading scales by 1.01225. An indicated 60 mph becomes 60.7 mph, and every 100 miles on the odometer is really 101.2 miles.
- How much does 255/40R18 change ground clearance over 245/40R18?
- The axle centerline moves by 0.16 inches — half the diameter change, because half the extra height sits below the hub and half above it.
- Will 255/40R18 fit where 245/40R18 fits?
- Nothing derived from the size code can answer that. Clearance depends on wheel offset, suspension travel and body dimensions that no tire size contains. This page tells you exactly what changes dimensionally, which is the part that can be calculated.
Related comparisons
Other tire maths on this site
- tire size calculatorRead any tire size code and get overall diameter, sidewall height, circumference and revolutions per mile, with the arithmetic shown.
- tire size comparisonPut two sizes side by side and see the difference in diameter, width, sidewall, ground clearance and speedometer reading.
- tire size chartEvery common size sorted by wheel diameter, with overall diameter in inches and millimeters and revolutions per mile.
- tire diameter calculatorOverall diameter, radius and rolling circumference from the size code, and the reverse — the sizes that produce a diameter you want.
- speedometer error calculatorHow far out your speedometer and odometer read after a tire size change, at any indicated speed.
- plus sizing calculatorLarger wheel, same rolling diameter. Plus one and plus two candidates ranked by how close they hold the original diameter.
- gear ratio calculatorThe axle ratio that restores stock engine rpm after a tire diameter change, plus cruising rpm at any speed.
- metric to inch tire conversionConvert a metric size such as 285/70R17 to its inch equivalent, and an inch size such as 33x12.50R17 back to metric.
- rim width rangeThe rim widths a size is designed to mount on, and how section width changes as the rim gets wider.
- tire size meaningWhat every character in 265/70R17 stands for, digit by digit, including the load index and speed rating.