Is 285/60R20 bigger than 265/60R20?

285/60R20 is 0.94 inches taller and 20 mm wider. In overall diameter that is +2.91%, which stays inside the ±3% rule of thumb for a substitution.

How much will 285/60R20 throw off my speedometer?

Every reading scales by 1.02906. An indicated 60 mph becomes 61.7 mph, and every 100 miles on the odometer is really 102.9 miles.

How much does 285/60R20 change ground clearance over 265/60R20?

The axle centerline moves by 0.47 inches — half the diameter change, because half the extra height sits below the hub and half above it.

Will 285/60R20 fit where 265/60R20 fits?

Nothing derived from the size code can answer that. Clearance depends on wheel offset, suspension travel and body dimensions that no tire size contains. This page tells you exactly what changes dimensionally, which is the part that can be calculated.

265/60R20 vs 285/60R20

285/60R20 is +0.94″ in overall diameter and +20 mm in section width against 265/60R20 — a diameter change of +2.91%, which stays inside the ±3% substitution rule. An indicated 60 mph would really be 61.7 mph.

Within 3%

Every dimension

Difference between 265/60R20 and 285/60R20
Dimension	265/60R20 → 285/60R20	Change
Overall diameter	32.52″ → 33.46″	+0.94″ (+2.91%)
Section width	265 mm → 285 mm	+20 mm (+7.55%)
Sidewall height	159.0 mm → 171.0 mm	+12.0 mm
Rolling circumference	102.16″ → 105.13″	+2.97″
Revolutions per mile	620.2 → 602.7	−17.5
Axle height / clearance	16.26″ → 16.73″	+0.47″

265/60R20265 mm

285/60R20285 mm

265/60R20 32.52″285/60R20 33.46″

Which is taller, 265/60R20 or 285/60R20?

285/60R20 is the taller of the two, at 33.46″ against 32.52″. The gap is 0.94 inches, or 24.0 mm.

Both are metric sizes, so neither states its height directly. Both figures below are derived from the section width, aspect ratio and wheel diameter in the code. 265/60R20 is 265 mm wide with a 159.0 mm sidewall on a 20″ wheel; 285/60R20 is 285 mm wide with a 171.0 mm sidewall on a 20″ wheel.

What the speedometer will read

Indicated versus actual speed after the size change
Speedometer reads	Actual speed	Error
25 mph	25.7 mph	+0.7 mph
40 mph	41.2 mph	+1.2 mph
55 mph	56.6 mph	+1.6 mph
60 mph	61.7 mph	+1.7 mph
70 mph	72.0 mph	+2.0 mph
80 mph	82.3 mph	+2.3 mph

Fitting 285/60R20 in place of 265/60R20 multiplies every speed and distance reading by 1.02906. Over 10,000 indicated miles the odometer is out by +291 miles.

Effective gearing moves by the same proportion. A vehicle with 3.73 axles running 265/60R20 would need 3.84 to keep the same engine speed on 285/60R20. Work it out for your own axle ratio.

Full specification of each size

265/60R20

Derived dimensions for 265/60R20
Dimension	Metric	Imperial
Section width	265.0 mm	10.43″
Sidewall height	159.0 mm	6.26″
Wheel diameter	508.0 mm	20.0″
Overall diameter	826.0 mm	32.52″
Rolling circumference	2,595.0 mm	102.16″
Revolutions per mile	385.4 / km	620.2 / mile
Measuring rim (estimate)	203 mm	8″

285/60R20

Derived dimensions for 285/60R20
Dimension	Metric	Imperial
Section width	285.0 mm	11.22″
Sidewall height	171.0 mm	6.73″
Wheel diameter	508.0 mm	20.0″
Overall diameter	850.0 mm	33.46″
Rolling circumference	2,670.4 mm	105.13″
Revolutions per mile	374.5 / km	602.7 / mile
Measuring rim (estimate)	229 mm	9″

Rim widths differ too: 265/60R20 is designed for 7.5″–9″ and 285/60R20 for 8.5″–10″. Their measuring rims differ, so the same wheel will not be ideal for both.

Can you swap one for the other?

Inside the ±3% rule

The diameter difference of +2.91% is within the ±3% that fitters use as the boundary for a substitution, so the speedometer, odometer and wheel-speed-derived systems stay close enough to calibration. The section width difference of +20 mm is a separate question and is the one that decides whether it rubs.

Neither figure says anything about physical fitment. Whether 285/60R20 clears the strut, the fender liner and the steering stops depends on wheel offset and suspension geometry that a size code does not encode. For maintenance rather than sizing, Car Basics covers tire care.