Is 285/60R20 bigger than 285/65R18?

285/60R20 is 0.88 inches taller and 0 mm wider. In overall diameter that is +2.69%, which stays inside the ±3% rule of thumb for a substitution.

How much will 285/60R20 throw off my speedometer?

Every reading scales by 1.02694. An indicated 60 mph becomes 61.6 mph, and every 100 miles on the odometer is really 102.7 miles.

How much does 285/60R20 change ground clearance over 285/65R18?

The axle centerline moves by 0.44 inches — half the diameter change, because half the extra height sits below the hub and half above it.

Will 285/60R20 fit where 285/65R18 fits?

Nothing derived from the size code can answer that. Clearance depends on wheel offset, suspension travel and body dimensions that no tire size contains. This page tells you exactly what changes dimensionally, which is the part that can be calculated.

285/65R18 vs 285/60R20

285/60R20 is +0.88″ in overall diameter and 0 mm in section width against 285/65R18 — a diameter change of +2.69%, which stays inside the ±3% substitution rule. An indicated 60 mph would really be 61.6 mph.

Within 3%

Every dimension

Difference between 285/65R18 and 285/60R20
Dimension	285/65R18 → 285/60R20	Change
Overall diameter	32.59″ → 33.46″	+0.88″ (+2.69%)
Section width	285 mm → 285 mm	0 mm (0.00%)
Sidewall height	185.3 mm → 171.0 mm	−14.3 mm
Rolling circumference	102.37″ → 105.13″	+2.76″
Revolutions per mile	618.9 → 602.7	−16.2
Axle height / clearance	16.29″ → 16.73″	+0.44″

285/65R18285 mm

285/60R20285 mm

285/65R18 32.59″285/60R20 33.46″

Which is taller, 285/65R18 or 285/60R20?

285/60R20 is the taller of the two, at 33.46″ against 32.59″. The gap is 0.88 inches, or 22.3 mm.

Both are metric sizes, so neither states its height directly. Both figures below are derived from the section width, aspect ratio and wheel diameter in the code. 285/65R18 is 285 mm wide with a 185.3 mm sidewall on a 18″ wheel; 285/60R20 is 285 mm wide with a 171.0 mm sidewall on a 20″ wheel.

What the speedometer will read

Indicated versus actual speed after the size change
Speedometer reads	Actual speed	Error
25 mph	25.7 mph	+0.7 mph
40 mph	41.1 mph	+1.1 mph
55 mph	56.5 mph	+1.5 mph
60 mph	61.6 mph	+1.6 mph
70 mph	71.9 mph	+1.9 mph
80 mph	82.2 mph	+2.2 mph

Fitting 285/60R20 in place of 285/65R18 multiplies every speed and distance reading by 1.02694. Over 10,000 indicated miles the odometer is out by +269 miles.

Effective gearing moves by the same proportion. A vehicle with 3.73 axles running 285/65R18 would need 3.83 to keep the same engine speed on 285/60R20. Work it out for your own axle ratio.

Full specification of each size

285/65R18

Derived dimensions for 285/65R18
Dimension	Metric	Imperial
Section width	285.0 mm	11.22″
Sidewall height	185.3 mm	7.29″
Wheel diameter	457.2 mm	18.0″
Overall diameter	827.7 mm	32.59″
Rolling circumference	2,600.3 mm	102.37″
Revolutions per mile	384.6 / km	618.9 / mile
Measuring rim (estimate)	216 mm	8.5″

285/60R20

Derived dimensions for 285/60R20
Dimension	Metric	Imperial
Section width	285.0 mm	11.22″
Sidewall height	171.0 mm	6.73″
Wheel diameter	508.0 mm	20.0″
Overall diameter	850.0 mm	33.46″
Rolling circumference	2,670.4 mm	105.13″
Revolutions per mile	374.5 / km	602.7 / mile
Measuring rim (estimate)	229 mm	9″

Rim widths differ too: 285/65R18 is designed for 8″–9.5″ and 285/60R20 for 8.5″–10″. Their measuring rims differ, so the same wheel will not be ideal for both.

Can you swap one for the other?

Inside the ±3% rule

The diameter difference of +2.69% is within the ±3% that fitters use as the boundary for a substitution, so the speedometer, odometer and wheel-speed-derived systems stay close enough to calibration. The section width difference of 0 mm is a separate question and is the one that decides whether it rubs.

Neither figure says anything about physical fitment. Whether 285/60R20 clears the strut, the fender liner and the steering stops depends on wheel offset and suspension geometry that a size code does not encode. For maintenance rather than sizing, Car Basics covers tire care.